Enabling MAC Filtering in WAG300N

How to enable the MAC Address Filtering in WAG300N.

Connect a computer to WAG300N.
Open Internet Explorer.
In the Address Bar type : 192.168.1.1 [Default IP Address of WAG300N].
In the Popup for username and password, type admin for username and admin for password [default].

• Once in the setup page, click on Wireless, the second tab on the top.
• Than select Wireless MAC Filter [third sub tab under wireless.
• Here you need to enable the option.
• In the Access Restriction, you need to specify whether u want to prevent or permit the computers from accessing the Internet.
• With firmware 1.01.01, you can list upto 50 Wireless MAC Addresses.
• If you click on the Wireless Client List in the same page, you can see the MAC Addresses of the Wireless [DHCP clients] devices connected to the router.
• The MAC Address is generally located at the bottom of the devices.

WRT150N with DU in U.A.E.

How to configure WRT150N in U.A.E with the ISP DU.

• Connect a computer to WRT150N to any of the 4 ports.


• Most of the times DU doesnt provide a modem cause its not required.


• There is a Ethernet [Cat5] cable that should be connected straight to WRT150N.


• Reset WRT150N for 20 seconds. The reset button is at the rear side of the router.


• Turn OFF the WRT150N. Power it ON after 5 seconds.


• Try Internet from the Computer connected to the router.


• You should be able to go online. You can change the name of the Wireless Network.


• Click on Wiereless Tab and configure the wireless settings there.


• This process applies to all Linksys routers like WRT54G, WRT54GR, WRT54GC, WRT54GL, WRT54GS, WRT100, WRT150N, WRT160N, WRT300N, WRT310N, WRT330N, WRT350N, WRT600N, WRT610N etc.

Wireless Range !

Tips to improve the Wireless Range.

How Can the Range of a WiFi Network Be Boosted? The wireless signal strength depends on many variables. Like the position of the Router / Access Point, interfering devices, thickness of the walls, the adapter/receiver on the computers. We will discuss some factors that will help boost the wireless range and performance.

The router should not be placed in an isolated part of the house. The router should not be placed near a Television set or any other electronic devise. Avoid placing the router in a cupboard or behind any thing. If the wireless router is against an outside wall of the house , the signal will be weak on the other side of your home. Common sources of interference in residences include brick or plaster walls, microwave ovens, and cordless phones. But there are many other ways to boost the signal of the wireless network. Try keeping the Access Point / Router elevated from the floor and away from any electronic device. Open the Setup page of the Router [the default IP Address is 192.168.1.1] and change the Wireless Channel. Try different combinations to best optimse the coverage. For N-Series devices, keep the Radio Band to 40 MHz Channel, Wide Channel to 9 and Standard Channel to 11-2.462 GHz. If you are using a N-Series Access point / Router, also use a N-Series adaptgers to enjoy the N-Series Connectivity. If you place the router is a central position of the house, the wireless range will be covered in the entire house [ofcourse depends on the size of the house] all the devices will be able to connect wireless without any hassel. The N-Series provides a maximum speed of 270MBPS. You can also replace the wireless antennas on the router to boost the range. Like high gain antennas. Or adjust the position of the antenna on the router or the computers to get better reception. Try using a Range Expander to extend the wireless signal. Keep the firmware on the router and the drivers on the adapter updated.

Configure WRE54G !

How to Configure WRE54G with any wireless Access Point to increase the Range ?


A Range Expander is the easiest way to expand the wireless network range or coverage. You don't need to use any wire connection to your network. The use of a Range Expander enables wireless connectivity in the areas of the house where the wireless signal of the existing Access Point / router is weak and where the cabling is impracticle. A Range Expander is a perfect solution to help cover large areas in multi-story homes, warehouse environments, public spaces, and wireless "Hot Spots" -- anywhere you need extra coverage for your wireless network. If the existing wireless network is unsecured, the installation of the Range Expander is very simple. Just plug it in and press the Auto Configuration button. The Expander will find your wireless network and configure itself automatically. The Linksys Wireless-G Range Expander works with most Wi-Fi certified access points and wireless routers. And it works in both Wireless-G and Wireless-B modes so you'll get the benefits of increased coverage even with a mixed network.

The Default IP Address of the Range Expander is 192.168.1.240 The default Password is admin. To get an optimal range from WRE54G, place it at a farther location where a computer still receives signal from your wireless router or access point. WRE54G uses WDS (Wireless Distribution System) to associate / synchronise with the wireless Access Point / Router. The setup CD will detect WRE54G when run from an wireless computer. You can use another WRE54G to expand the Range of the previous one but remember that the transmission speed coming from each Expander will be half that of the source.

Click here to check the updated list of firmwares for Linksys devices.

Cannot send/receive mails thru Outlook Express.

If you cannot Send or receive mails thru the Linksys router, follow these simple steps.

1) Reduce the MTU from the router's Setup Page.
2) Go to Administration and Gamin tab and trigger the Ports 25 and 110.
3) Powercycle the router and the computers. If Still doesnt work,Reset and Reconfigure the router.
4) If Still No luck, Upgrade the Firmware on the router. If the firmware appears to be the latest, Reflash the firmware.
5) If still doesnt work,Connect Using the ISP Modem,if cannot send/recv Mails. Contact the ISP.